If the correct selection has been made, you should see the GPS status icon change from red to green. Set the “Baud Rate” to 4800 and click “OK”. Some manufacturers make it obvious, like ”/dev/cu.MiniPlex-99000125“, but others may be more generic, like: ”/dev/cu.usbserial“. It is not always obvious which is the correct one, but in general the device will have a name starting: ”/dev/cu.“ or ”/dev/tty.“. Open the “Dataport” menu & select the device from the list. When the driver is installed and the device connected, start OpenCPN, select the Options icon and click the Connections tab. Both those companies make OS X drivers available on their web sites, but manufacturers of GPS devices usually package the driver with device. Nearly all hardware uses one of just two chip makes: those from FTDI or Prolific. Whether using a device with its own USB lead or via a serial-USB adapter lead or an NMEA multiplexer with USB port, the appropriate OS X driver needs to be installed. if this is the case, use the following fix:Īttaching a GPS device to a Mac is done via one of the USB ports. If it works, try running opencpn without sudo, chances are that you cannot see the gps. To check that it works (/dev/rfcomm0 under GPS NMEA data source). Your bluetooth GPS should now be working in open CPN. In a separate terminal, you can test the connection with You only need to to this once, not required if you reboot at this point). Sudo rfcomm release 0 (not strictly neccesary) # Automatically bind the device at startupĬhannel 1 #use channel number as provided by sdptool records XX:XX:XX:XX:XX:XX Pair GPS with bluetooth icon -break connection with bluetooth icon -get device id: sudo hcitool scan -get channel for gps: sdptool records 00:02:78:0A:4E:E9 (put your actual number here) -sudo gedit /etc/bluetooth/nf #edit rfcomm input file. That's it - you should now have a Bluetooth GPS Connected. Now in the NMEA Data Source options select from the pulldown menu: “ /dev/rfcomm0”, or write it in the box, if not present as an alternative. Now all you need to do is go into OpenCPN Toolbox and select GPS. Note put your GPS address in this line You should not have to run these commands each time your linux is restarted as it will remember your GPS address. Next we have to bind the GPS address to a “virtual” device OpenCPN understands in this case rfcomm0. In this case I have a IBT-GPS at address 00:1C:88:10:D3:4D (Your GPS address will be different) It will then start looking for the Bluetooth GPS and hopefully find your GPS. Once you have done that you will need to find what the address of the GPS is. Instead, if you need GPS, buy the BT GPS Sensor that Phil is selling, and save yourself from frustrations, time wasted and money "spent" on work arounds.If you have a bluetooth GPS you will need to first configure it through the standard Ubuntu Bluetooth “set up new device ” proceedure. I recommend you not buy this "Localizer" program or make a decision to buy a laptop just because it has this "GNSS" chip. No warranty is given or implied as to the accuracy or availability of location information. It is provided "as-is", and intended for recreational use only. Under NO circumstances should this product be used for precision navigation.At higher rates of speed, the displayed map position may lag behind the actual vehicle position. The Windows location platform is limited to a 1hz refresh rate (once a second).It DOES NOT represent the quality of the actual GPS/GNSS signal and is provided for protocol compatability only. The number of active satellites and signal strength is simulated.However, do read the fine print/limitations: Centrafuse Localizer (which is unfortunately not freeware) to bypass Windows Location Provider which is useless Install driver from Lenovo (which makes Broadcom GNSS work properly) QGIS (tested with version 2.0. Shame on Broadcom and other manufacturers for not having this "bridge" available natively. Some people have reported success with this. The only application I found that does that is: Centrafuse Localizer and it costs $15. The only way to make it work is to find software that creates a virtual COM port and links and translates the sensor data to NMEA format. If you are like me, and have already bought a tablet because it had an integrated GPS you will soon find out that it will not work with your favorite software! TunerstudioMS, GarminPC, OziExplorer, Sygic Fleet, PC Navigator and many others require connection over a standard com port. If you are buying an x86/圆4 Windows 8 or 8.1 tablet or a laptop with GPS/GNSS sensors, be advised that they will not work with TunerStudioMS or any other PC application that requires communication over NMEA 0183 protocol.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |